Pleated Filter Cartridge: Star vs Oval vs Custom Pitch
Blog · 20 November 2026 · 10 min read
TL;DR: No published study compares star, oval and custom-pitch pleated filter cartridges head to head. The outline of a pleated filter cartridge should therefore follow the cage and tube sheet, and pleat ratio decides how well the element cleans. In a 2019 laboratory study, Li et al. concluded that pleat ratio should stay below 1.59, with the lowest growth rate of the resistance coefficient at pleat ratios of 1.15 to 1.59. No published pleat-count limit exists for fine sticky dust, and no published data ranks spunbond against needle felt for pleated elements. A pleated filter cartridge is best specified by pleat ratio, media, surface layer and temperature rating, with the collector drawing and dust profile attached.
What does a pleated filter cartridge trade for its extra area?
A pleated filter cartridge is a replaceable element whose media is folded around a core so that more filtration area fits in the same housing. In a baghouse, that extra area is the whole case. Masturlal's position is that air-to-cloth ratio is fixed at design by gas volume and cloth area, so a same-size replacement bag cannot change it, and more area in the existing cages needs a different geometry. Masturlal launched PleatMax pleated filter elements in 2013 for that job, as capacity upgrades without a structural rebuild.
Folded area and working area are different numbers. Bending and creasing compress, deform and crowd the medium, and Li et al. (2019) cite Wakeman et al. as linking all three to lost effective area.
Li et al. (2019), writing in , cite Kim et al. as showing an effective filtration area of approximately 50 to 60% of the theoretical area for the pleated cartridges they studied.
Nominal area is a ceiling, never a design value. A quote that gives catalogue area alone says little about the air-to-cloth ratio the collector will actually run at.
Pleat ratio, not the star or oval outline, decides how well a cartridge cleans
Pleat ratio is pleat height divided by pleat pitch, as Li et al. (2019) define it. Deep, closely spaced pleats give a high ratio and more area, while shallow, open pleats give a low ratio and wider channels for dust to leave. In tests on conventional and coated media, the same authors found that regeneration efficiency fell gradually as pleat ratio rose, that coated media regenerated better, and that the pleat-ratio effect on pressure drop grew more obvious at higher filtration superficial velocity.
In 2012, Park, Lee, Jo and Kim reported optimum operation at a pleat height-to-pitch ratio of 1.48 for one PTFE/glass composite pleated filter. Above 1.48, pressure drop rose and the cleaning interval shortened because the filter became harder to clean. That result and the 1.59 ceiling are compatible, but they come from different media and test rigs, so neither is a universal design value.
Pleat depth is a trade, not a free gain. Théron et al., cited by Li et al. (2019), found lower pressure drop in three laboratory prototypes with a small pleat height and a large pleat width, toward a flat geometry. Deeper pleats add nominal area but narrow the channel the pulse has to clear, which is how a higher ratio ends in a higher pressure drop.
Pleat shape inside the outline counts as well. Cheng et al. (2024) present the 1.59 finding as one for triangular pleats, and cite simulation studies by Teng et al. (2022) and Chen et al. (2017) reporting better filtration and cleaning for trapezoidal pleats than for triangular ones. Those results are simulated and say nothing directly about star or oval cartridges.
Before a pleat ratio goes into the RFQ, see how Masturlal matches media to cement, steel, aluminium and ferro-alloy dust profiles.
Which pleated dust collection filter cartridge fits your cage and tube sheet?
The tube sheet decides the outline, and the dust decides the pitch. Masturlal makes PleatMax as star, oval or custom pitch. No published comparative data ranks one outline above another, so the comparison below rests on fit and pleat spacing.
| Geometry | Where it fits | Pleat spacing | Main cleaning risk | Choose it when |
|---|---|---|---|---|
| Star-pleated (round) | Round holes and round cages | Fans out from the core, tightest at the root | Dust bridging at the roots | Retrofitting round bag positions on a fixed hole pattern |
| Oval | Oval openings, close row spacing | Near-uniform on the flats, tighter at the end radii | Crowding at the end radii | The collector was built for oval bags, or rows are too close for a round element |
| Custom pitch | Either outline | Set to a target pleat ratio, not a maximum count | Less nominal area | Fine, sticky or cohesive dust, or a history of blinding |
A star-pleated element is a round cartridge whose pleats radiate from a cylindrical core, so crowding concentrates at the roots. Pleat crowding is one of the effects Wakeman, Hanspal, Waghode and Nassehi analysed in 2005, with medium compression and pleat deformation. An oval element moves that crowding to its end radii and in return fits openings and row spacings that a round element of similar area cannot.
Custom pitch is the answer when the dust, not the hole, is the constraint, accepting less nominal area for pleats the pulse can actually clear. Where a round position needs no extra area at all, a conventional pulse-jet filter bag remains the simpler part.
How many pleats is too many for fine sticky dust?
No published pleat count marks the limit for fine sticky dust; the working ceiling is set by pleat ratio and by whether the pulse can clear the pleat roots. Research published in 2024 by Cheng et al. describes triangular-pleat cartridges as prone to clogging on sticky dust, with a significant loss of filtration capacity, and notes that pleated media can clog and gain resistance over prolonged use.
Li et al. (2019) add, citing earlier work, that cartridges with many folds are harder to clean than cylindrical bags and can clean patchily. Their below-1.59 conclusion was not framed around sticky dust, and no pleat ratio converts into a pleat count without the pleat height and element diameter. Two points change in the specification.
Specify pleat ratio, and open the pitch first. Two elements with the same pleat count can have very different channels if their pleat heights or core diameters differ, and deeper pleats add nominal area that fine sticky dust can bridge. State the target ratio on the RFQ and ask for the pitch at the pleat root.
Consider pre-coating with a low-viscosity dust. In comparative tests, Cheng et al. reported cleaning-cycle reduction rates of 45.99% and 15.89% for two loading methods and concluded that pre-cladding can improve early-stage filtration efficiency and cleaning performance. Their abstract does not say which figure belongs to which method, and the tests used a small media testing platform rather than cartridges in service.
Pulse pressure and cleaning mode finish the job
Masturlal's guidance for pulse-jet collectors is to clean on demand from pressure drop, at the lowest pulse pressure that holds ΔP stable, and to confirm with CFD pulse-mapping and valve audits that pulse energy reaches every row. Over-cleaning, in Masturlal's view, flexes and wears the media. That rule assumes the element can clean at low pressure in the first place, which is a geometry question as much as a settings one.
In 2005, Lo, Chen and Pui tested six pleated cartridges in a full-size pulse-jet dust collector. Tank pressure proved critical to cleaning while pulse duration had little effect, and pleat ratio had a great effect on which mode worked: clean-on-time performed better on high pleat ratio filters, clean-on-demand on low ones. Particle concentration during pulsing was at least two times that during filtration for all six cartridges.
Read together, the two suggest that a low-ratio element suits on-demand cleaning, while a deep, high-ratio element may need a timed cycle to stay clean.
Is spunbond or needle felt better for a pleated filter cartridge dust collector?
No published comparative data ranks spunbond against needle felt for pleated dust collector elements, so a supplier's verdict either way is a claim, not a finding. Masturlal builds PleatMax in either ComPac® needle felt or spunbond, each with ultra-microfibre surface layers, which moves the decision onto the application.
Media thickness is the mechanism to weigh. Choi, Lucius, Kim and Koo (2021) identify filter height, pleat pitch and media thickness as shape parameters affecting pressure drop alongside filter material, though their work covered low-height pleated filters for respirators. A thicker medium fills more of each pleat channel, so a felt element needs a coarser pitch and fewer pleats than a thinner spunbond one to keep the same open channel.
What do microfibre surface layers add to pleated media?
An ultra-microfibre surface layer is a layer of very fine fibres on the dust side of the media that captures particles at the surface instead of letting them embed. Masturlal builds these layers from 13 to 15 µm microfibres and argues that surface-held dust pulses off cleanly, keeping pressure drop low and stable.
Published support for surface treatment is real but general. Lo, Chen and Pui found in 2005 that surface-treated cartridges were superior to untreated ones on the same base media, and Li et al. (2019) found coated media regenerated better than conventional media. Neither identifies a microfibre layer or compares spunbond with needle felt.
Temperature limits by media cap the pleated element
The temperature rating of the finished pleated element, not a fibre's own limit, caps what a pleated product can take. An undated overview by 360iResearch lists temperature and chemical compatibility among cartridge selection factors, alongside media, geometry, pressure drop, cleanability and service life.
Where gas runs hotter than the pleated element's rating, felt bags, or the fibreglass Masturlal uses in its reverse-air filter bags, are the alternative. The rating of the specific media grade, spunbond included, belongs on the quotation, with peak temperature and acid dew point.
Send these drawings and data with the RFQ
Masturlal does not publish a standard filtration area per PleatMax element, so the area worth having is the one calculated for your drawing. The same 360iResearch overview advises validating performance under representative operating conditions rather than relying solely on nominal specifications, and the RFQ is where that begins.
Tube-sheet drawing. Show hole outline and size, centre-to-centre spacing, row count and clear length below the tube sheet. Round holes take a star-pleated or custom-pitch element; oval openings take an oval one.
Current bag specification. Give the diameter, length, media, closure and quantity installed now. That is the baseline any area gain is measured against.
Dust profile. Describe chemistry, particle size, moisture and whether the dust is sticky, hygroscopic or oily. These set the pitch, the pleat ratio and the surface layer.
Gas conditions and emissions target. State gas volume, continuous and peak temperature, and the stack limit to meet. Temperature selects the media, and the emissions target shapes the surface layer.
Pulse system and ΔP history. Record tank pressure, valve type, cleaning mode and the recent pressure-drop trend. Lo, Chen and Pui found tank pressure critical to cleaning, so it belongs on the sheet.
Ask in return for pleat height, pitch, count, pleat ratio, nominal area with its test basis, and the temperature rating of the exact media grade. A quote without a pleat ratio leaves the most important cleaning variable unspecified.
Sources
Influence of pleat geometry on the filtration and cleaning characteristics of filter media - ScienceDirect (Théron et al., as cited in Li et al., Separation and Purification Technology (Elsevier))
Experimental study of pleated cartridge filters in a pulsejet-cleaned dust collector (Feng, Geng, Teng and Gui (ENVIRON SCI POLLUT R), 2023-01-01)
Effect of pre-cladding dust layer on filtration and pulse-jet cleaning performance of filter media - ScienceDirect (Jin et al. (2023), as cited by Cheng et al. in Process Safety and Environmental Protection, 2023-01-01)
Analysis of Pleat Crowding and Medium Compression in Pleated Cartridge Filters | Request PDF (Sanaei and Fong, Physics of Fluids, 2022-09-01)
Pleated Filter Cartridge (360iResearch)
Frequently asked questions
- What pleat geometry is best for dust collector cartridges?
- No published study names star, oval or custom pitch as the best pleat geometry for dust collector cartridges. The tube sheet sets the outline and the dust sets the pitch. For cleanability, pleat ratio matters most: Li et al. (2019) concluded from laboratory tests that pleat ratio should stay below 1.59.
- Is spunbond or needle felt better for pleated filter elements?
- Neither spunbond nor needle felt has been shown better for pleated filter elements, because no published data compares the two. The choice rests on temperature, chemistry, abrasion and pleat spacing, since thicker media fills more of each pleat channel. Masturlal offers PleatMax in ComPac® needle felt or spunbond, both with ultra-microfibre surface layers.
- How many pleats is too many for fine sticky dust?
- No published pleat count sets the limit for fine sticky dust. Cheng et al. (2024) describe triangular-pleat cartridges as prone to clogging on sticky dust, so a lower pleat ratio, a more open pitch and a surface layer make the safer specification. Pleat ratio cannot become a pleat count without pleat height and diameter.
- Does a pleated cartridge work at its full catalogue filter area?
- A pleated cartridge does not necessarily work at its full catalogue area. Li et al. (2019) cite Kim et al. as finding an effective filtration area of approximately 50 to 60% of the theoretical area for the cartridges studied, because pleating compresses, deforms and crowds the media. Nominal area is a ceiling.
- What temperature can PleatMax pleated elements handle?
- PleatMax pleated element temperature ratings depend on the media, and the element rating, not a fibre's own limit, caps the pleated product. Specify continuous and peak gas temperature and acid dew point on the RFQ, and ask for the rating of the exact media grade. Where gas runs hotter than that rating, felt filter bags are the usual alternative.
- Should pleated cartridges be cleaned on a timer or on demand?
- The right cleaning mode for pleated cartridges depends on pleat ratio. In a 2005 study by Lo, Chen and Pui, clean-on-time worked better on high pleat ratio cartridges and clean-on-demand on low pleat ratio cartridges. Masturlal's general guidance is to clean on demand from pressure drop, at the lowest pulse pressure that keeps ΔP stable.
Specify your PleatMax elements with Masturlal
Send Masturlal the tube-sheet drawing, dust profile and gas temperature, and ask for the pleat ratio, pitch and media grade behind every quoted area. To see which media Masturlal pairs with each dust, review Masturlal's industry-by-industry media guidance.